[928uk] S4 High idle update
Brian Butterworth
brianb at cheerful.com
Sat Mar 12 21:46:36 UTC 2016
Hi Paul, Yes the throttle plate was removed to replace the shaft bearings. I took lots of pictures of the plate and the springs, the plate is the correct way round and I wired the springs and washers together so not to loose the order. Dwayne's guide was quite comprehensive on this area. When I first reassembled the plate it didn't close properly, so I loosened the screws and operated the lever arm where the plate seated itself (or appeared to).The plate opens and closes fine when cold, is there a procedure for aligning the plate? Or is it just a mater of trial and error? I know what you mean about the dangers of driving with a stuck open throttle, trying to park an auto at 5,000rpm isn't recommend. I've already lifted the intake, takes about an hour now.
Regards Brian 88 S4 auto
Sent from my Samsung device
-------- Original message --------
From: Paul Lacey <t595 at btopenworld.com>
Date: 12/03/2016 18:20 (GMT+00:00)
To: Brian Butterworth <brianb at cheerful.com>, 928uk <928uk at lists.928.org.uk>
Subject: Re: [928uk] S4 High idle update
Hi Brian,I presume this high idle has been since intake refresh ?Has the throttle butterfly been removed from it's spindle at any stage ? The throttle butterfly is very sensitive to the position it is done up in, which way round it is (there are punch marks done by the factory), AND especially the spindle return spring. It is very easy to get the spindle return spring and associated thrust washers / spacers incorrectly assembled such that you have much less return force exerted by the spring on the butterfly.
I'm sure you have found the cause if you can see a gap when the throttle should be closed. It's actually dangerous to drive like that.So, effectively, you have a leak. There really are not many things that can give a high idle.I have not tried but I think it could be possible to remove the throttle assembly (and rubber pipes) without removing the manifold - it's certainly worth half an hour trying !I find a folded blanket over the top of the engine means you can lie with your chest on the inlet manifold and get better access to things underneath, the other vital component being very good lighting.Good luck with it Best Regards,Paul Lacey
From: Brian Butterworth via 928uk <928uk at lists.928.org.uk>
To: 928uk <928uk at lists.928.org.uk>
Sent: Saturday, 12 March 2016, 16:18
Subject: [928uk] S4 High idle update
Update on my idle speed issues. I've been experiencing high idle rpm once the engine is warm. Did full intake refresh last year, pretty certain it isn't a leak. Changed the ISV, TPS also.
Changed the throttle cables today, adjusted and test driven, high idle back after 5 minutes. 5,000rpm which was more than I was prepared to attempt parking with.Checked the cable quadrant and there was slack in the throttle cable and no clicking from the TPS opening or closing. Diagnosed the throttle valve is sticking open when warm independent of cables. I could see it open with a torch and mirror with the MAF removed.The intake is off again the when cool the throttle valve is closed.I need to test the throttle body hot and cold before rebuilding, I'm thinking of putting it in the oven at say 85C.
Any other suggestions before I take it apart, I'd like to recreate the sticking valve and then fix, and test again, to save keep removing the intake.
Any ideas why the valve would stick when warm, I would have thought it's designed to be set cold and allow for heating.
Regards Brian 88 S4 auto
Sent from my Samsung device
_______________________________________________
928uk mailing list
928uk at lists.928.org.uk
http://lists.928.org.uk/mailman/listinfo/928uk
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://lists.928.org.uk/pipermail/928uk/attachments/20160312/2f5456f9/attachment.htm>
More information about the 928uk
mailing list